How to lay block paving

Grey block paving

This article is a beginners guide to laying block paving. It will look at how block paving should be constructed. The good news is that block paving can be done by anyone who is handy enough and has the patience to learn. The bad news is that it is quite hard to master and very time consuming. 

Don’ let that put you off tho, building your own block paving can be very rewarding and save you a lot of money. 

The first part of the guide covers the basics of laying block paving. The second part looks at laying block paving on different surfaces and the extra steps that need to be taken.

Part 1: Steps to lay block paving

Step 1: Clearing the area

Digging out an area before creating terraces

The area where you want to lay block paving will need to be cleared and leveled before you begin. Block paving needs an even, firm base or it is likely to sink over time.

Work out beforehand how deep you will need to dig in order to lay the block paving. This needs to include the sub base, sand base and block depth. Mark out the area and make sure you have somewhere to dump the waste when it is taken out. You can pile it up and then hire a grab waggon to take it away.

For larger areas it may be a good idea to hire a mini digger because digging through clay and compacted soil can be tiring. As a rough idea it takes about an hour of vigorous digging to take out one square meter of hard soil down to a depth of 5 inches.

Step 2: Sub base

A sub base of crushed rock or hardcore needs to be laid and compacted using a wacker plate. The depth of  the sub base depends on what you are going to use the area for. The heavier the usage the thicker the sub base will need to be.

For driveways which will have cars on them it’s a good idea to have 50 – 100mm of sub base. For patios you may be OK with no sub base provided the soil is compact and level underneath.

Step 3: Base

The base layer should be made up of 50mm of damp sharp sand which is levelled using wooden rails. The blocks will be laid directly on top of the sand so it needs to be evenly spread and completely level. Use a spirit level to make sure the rails and flatten board are perfectly level.

The base will be compacted after the blocks are laid so make sure it is 10mm above the desired level.

Step 4: Edges

Block paving path border

Block paving needs to be retained by firm edges in order to support the block paving. Any gaps at the edges will mean the blocks can move and sink.

An edge can be a house wall, a concrete border or any other feature which has sufficient strength to hold the blocks in place.

Step 5: Block installation

After the sand base is laid its time to put the blocks in. You can’t stand on the the sand base so ensure you have a plan which works for the area you are block paving.

Most block will have spacing nodes which will ensure they are the correct distance apart if you push them as close together as possible. Start from one flat surface and work outwards.

It’s likely you will have some awkward parts around the edges. You will need to cut blocks to fit into these spaces. This can be done with a block splitter or an angle grinder. Both can be rented or bought from most tool shops.

Lay the blocks without worrying about their exact level in relation to each other. After the blocks are all laid, go over the surface again with a whacker plate until they are all satisfactory level. Usually 1 – 3 times will do it.

Tip: Make sure you know what pattern you want before laying or you may have to go back and fix it.

Step 6: Sand

The final step is to fill the gaps in the block with sand. Fine dry sand should be purchased for this. Sprinkle the sand onto the surface and use a brush to sweep it into the gaps.

This stage should only be done when the surface is dry.

Step 7: Sealing block paving (optional)

Resin sealed block paving

This is an entirely optional stage but should be mentioned for its benefits. Block paving can last for decades however it does require some upkeep. Over time the sand in the joints can vanish, leaving the blocks wobbly and uneven. Re sanding the paving once every 2 years is usually enough to stop this. Using a high quality sealant can hold the sand in place which reduces the need to replace it.

Weeds are probably the main issue that we have seen with block paving. No matter that you do, they will find their way into the joint eventually. The only permanent way to stop weeds in block paving is to seal the joints.

Completed

If you follow these steps careful you will be left with something to be proud of. Each stage takes some practice but is easy to pick up. Block paving can be used as soon as it is completed so you can enjoy it immediately.

If you have decided that it may be work than you are willing to do then we would love to offer our services to you. Acorn Gardening can lay block paving at a fast pace and have your new driveway or patio ready to go in no time.

Part 2: Laying block paving on different surfaces

Laying block paving on soil

Block paving should never be laid directly onto soil. Soil will not compact in an even way under the blocks and will result in an uneven surface. However, if you are block paving a patio you don’t need to go too deep into the soil with the base. If the soil is firm then you can just use a sand base and skip the crushed rock sub base.

Summary: skip the sub base step above and follow the rest of the process as normal.

Laying block paving on a slope

Lots of us have sloped gardens and driveways which are impractical to level. We still want them to look good and be useful. Laying block paving on a slope can be done but involves some extra work.

Block paving is held together by tension and gravity. This means that if there is any room to move, the structure will be compromised and the blocks will move over time.

When laying block paving on a slope the number rule is to make sure the slope is uniform. If it is steeper at one end than that the other there will be areas where the blocks are not connecting properly. Over time the sand will shift and the blocks will move.

If you have an uneven slope in your garden you may need to get it leveled before installing block paving.

A second option is to install midway restaining courses. This means inserting concrete barriers at points throughout the block paving. By doing this you will keep the blocks in each section compact. It also means if there is slippage it will be much easier to fix because it is confined to one section.

Laying block paving on a concrete base

Concrete can be a great replacement sub base for block paving. Providing your concrete surface is uniform and reasonably level you can treat it as you would a compacted sub base.

If your concrete is in poor condition with large holes or it is starting to fragment you will need to remove it and start again. Damaged concrete will create an uneven sub base which will eventually distort the blocks.

Hire us

We hope this guide has been useful

Acorn Gardening are professional block paving installers. We can advise you on the best approach to block paving any area.

For a quote or to discuss your requirements get in touch today!


You can find out how much your block paving would cost in an instant here.

Close Menu